Notes on optional accessories (don't forget to select your accessories from the options above): - Ceiling kit is used to conduct condenser discharge air to drop ceiling ventilated plenum. Kit consists of flange, flex duct and ceiling panel.
- Nozzle kit is used in place of indoor air discharge grille to direct conditioned air to specific spots. Kit consists of drop-in panel with two flex-duct nozzles.
- Pump kit is used in place of standard condensate collection tank to remove condensate from unit. Kit consists of pump, wire harness and hardware.
- Condenser plenum is used to direct a supply of condenser inlet air to the unit from outside the space to be cooled. When using a condenser plenum, order additional CK-12 (or 2 CK-12 in the case of model 60's) for conducting condenser inlet air.
- Evaporator plenum is used to direct evaporator return air from a remote location or room to the unit. Flex duct to be supplied separately.
- Discharge duct adapter is used in place of standard evaporator air discharge grille to transform opening to round duct. Flex duct to be supplied separately.
OceanAire PAC Accessory Options
AirBoss Standard Features - High Efficiency Rotary or Scroll Compressor
- Rifled Copper Tube, Enhanced Fin Coils
- Commercial Grade Steerable Casters
- Manual Reset High Pressure Switch
- Washable Air Filters
- 5-Gallon Condensate Tank AutoShut-off
- Condensate pump on 5-Ton AirBoss
- Electronic Thermostat
- 24 Volt Control System
- Pitched Drain Pan (ASHRAE 62-89)
- Automatic re-start after loss of power
- Optional Drop-in Nozzles
- Optional Duct Adapters
- Can Easily Remote locate thermostat
- 10 foot power cords
- Schrader valves for service & Testing
- 5-year compressor warranty
- Made in U.S.A.
- Cools to 60° F
OceanAire AirBoss Portable Cooling Unit Dimension Diagram
NOTE: Condenser inlet air plenum adds 13 inches to dimension “C” AirBoss PAC6034 Specifications: | Mechanical | | | Height | (A) with Casters: 52.25 in. (132.72 cm.)
(D) w/out Casters: 48 in. (122 cm) | | (B) Width | 28 in. (71 cm.) | | (C) Depth | 39 in. (99 cm.) | | Weight | 515 lbs. (234 kg.) | | Shipping Weight | 555 lbs. (252 kg.) | | Shipping Volume | 48 cu.ft. | | Cooling | | | Cooling Capacity1 | 60,050 | | Cooling Amps6 | 14.8 | | Cooling Watts6 | 6000 | | Voltage (V/Phase) at 60Hz | 460/3 | | In Rush Current (Amps) | 140 | | Plug Type | L16-20P | | EER3 | 10.0 | | Compressor | | | Compressor HP | 5 | | Compressor RLA | 9.0 | | Compressor LRA | 62 | | Evap | | | Evap CFM4 | 1950 | | Evap Motor HP | 1 | | Evap Motor Watts | 550 | | Condenser | | | Condenser CFM | 2200 | | Condenser Motor HP | 1 | | Condenser Motor Watts | 750 | | Condensate | 20 ft (Pump -STANDARD) | | Sound Level5 | 78 | | R-410A Charge Oz. | 80 |
Specifications subject to change without notice:
1 Cooling Capacity is total BTUH at 80ºDB/67ºWB return air, at high fan speed
2 Time Delay fuses/circuit breakers are recommended
3 EER is determined at high fan speed, with condenser discharge air ducted into another area
4 CFM with free discharge
5 Sound Pressure, dB at 5 feet, commercial operation
6 Amps & Watts at 208 Volts Ambient operating range 65º to 105º May operate down to 55º if equipped with hot gas bypass (Factory installed) | 
